The Basics of Plumbing Knowledge When Installing a Bathtub
The Basics of Plumbing Knowledge When Installing a Bathtub
Blog Article
The article author is making a few great pointers on the subject of Installing A Bathtub overall in this article directly below.
:max_bytes(150000):strip_icc()/installing-a-tub-or-shower-surround-2718986-01-b02d6683a8ee4621bf9b9ac7ab0b1dd2.jpg)
Setting up a tub isn't specifically brain surgery, however it does require strong plumbing, carpentry, and often, tiling abilities. Replacing an old tub with a brand-new one is also a moderately tough project. If the old bathtub is conveniently easily accessible, the job can move quickly; if you need to open a wall surface to remove the old tub as well as place the new bathtub, the job is a lot harder. In either case, the job is within a residence handyman's skills, although you will certainly need an assistant to vacate the old bathtub as well as embeded in the brand-new one. Make certain you have actually qualified on your own for the work as well as are comfortable attempting it. Instead of hiring a professional to take control of a halfway-completed job, it is better to take into consideration employing one before you begin. Chances are you may require an expert plumber to make tube links.
This article will help you install a brand-new bathtub in your restroom if you have actually currently acquired a new tub and also do not need to alter the arrangement of your previous supply of water pipes.
Your devices and product list ought to comprise the following:
Planning for the Installation
Firstly, the supporting frame supplied with the bath needs to be fitted (if needed) according to the supplier's directions. Next off, fit the taps or mixer to the bathtub. When suitable the tap block, it is essential to make certain that if the tap comes with a plastic washing machine, it is fitted in between the bathroom and the taps. On a plastic bath, it is additionally practical to fit a supporting plate under the taps system to prevent stress on the tub.
Fit the versatile tap adapters to the bottom of both faucets making use of 2 nuts and also olives (in some cases supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and then pass the electrical outlet via the hole in the bathroom. Make use of the nut provided by the producer to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the flexible overflow pipe to the overflow outlet. After that, screw the pipeline to the overflow face which must be fitted inside the bathroom. Make sure you use every one of the provided washers.
Link the catch to the bottom of the waste outlet on the bathtub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and screw on the trap to the outlet. Connect all-time low of the overflow tube in a similar manner.The bathroom ought to now prepare to be fitted in its last placement.
Removing Old Touches
If you require to change old taps with new ones as a part of your installment, after that the first thing you ought to do is disconnect the supply of water. After doing so, turn on the taps to drain any type of water staying in the system. The process of removing the existing taps can be rather problematic due to the limited gain access to that is usually the instance.
Make use of a container wrench (crowsfoot spanner) or a faucet tool to reverse the nut that links the supply pipes to the faucets. Have a towel all set for the remaining water that will certainly come from the pipelines. As soon as the supply pipes have been gotten rid of, use the very same device to loosen up the nut that holds the taps onto the bath/basin. You will certainly require to stop the solitary taps from transforming throughout this process. Once the taps have actually been gotten rid of, the holes in the bath/basin will certainly need to be cleaned of any type of old sealing substance.
Before moving on to fit the new faucets, contrast the pipeline links on the old faucets to the brand-new faucets. If the old taps are longer than the new taps, then a shank adapter is needed for the brand-new taps to fit.
Mounting the Tub
Making use of the two wooden boards under its feet, put the bathtub in the needed setting. The wood boards are practical in evenly spreading the weight of the bath tub over the area of the boards rather than focusing all the weight onto 4 small points.
The next objective is to guarantee that the bath tub is leveled all round. This can be attained by checking the level and also changing the feet on the bathtub up until the level reviews level.
To set up taps, fit the bottom of the furthest versatile faucet adapter to the proper supply pipe by making a compression join; after that do the same for the other faucet.
Activate the supply of water and also check all joints as well as new pipework for leakages and also tighten them if necessary. Fill the bathtub as well as also examine the overflow electrical outlet and the normal electrical outlet for leakages.
Lastly, fix the bathroom paneling as described in the supplier's instruction manual. Tiling as well as securing around the tub must wait till the bath tub has actually been made use of at the very least once as this will certainly settle it right into its final position.
Suitable New Taps
If the tails of the new faucets are plastic, then you will need a plastic port to stop damages to the thread. One end of the connector fits on the plastic tail of the faucet and also the various other end supplies a connection to the existing supply pipes.
If you require to fit a monobloc, after that you will call for decreasing couplers, which attaches the 10mm pipe of the monobloc to the common 15mm supply pipe.
Next off, place the faucet in the installing hole in the bath/basin guaranteeing that the washing machines remain in place in between the faucet and the sink. Protect the faucet in position with the maker offered backnut. When the tap is safely in position, the supply pipelines can be connected to the tails of the faucets. The taps can either be attached by utilizing corrugated copper piping or with normal faucet connectors. The former type must be attached to the faucet finishes initially, tightening up only by hand. The supply pipelines can later on be connected to the various other end. Tighten both ends with a spanner after both ends have been connected.
Tiling Around the Bath tub
In the location where the bath satisfies the ceramic tile, it is essential to seal the accompanies a silicone rubber caulking. This is essential as the installation can move enough to break a stiff seal, causing the water to pass through the wall surface between the bathroom and the tiling, bring about difficulties with wetness as well as possible leaks to the ceiling listed below.
You can select from a variety of coloured sealers to blend in your components and fittings. They are marketed in tubes as well as cartridges, and also can sealing gaps as much as a width of 3mm (1/8 inch). If you have a bigger void to load, you can fill it with spins of drenched newspaper or soft rope. Keep in mind to constantly load the bathtub with water before securing, to allow for the movement experienced when the tub is in usage. The sealer can split relatively very early if you do not consider this activity before sealing.
Conversely, ceramic coving or quadrant floor tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are also conveniently offered on the market. It is suggested to fit the tiles using waterproof or water-proof adhesive and grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
As a keen person who reads about Tools You Need to Install a New Bathtub , I imagined sharing that excerpt was really helpful. Do you know about someone else who is fascinated with the topic? Do not hesitate to share it. Kudos for your time. Please check our site back soon.
Plumbing integrity assured. Report this page